Optional accessories for the INS-AX2 series, INS-AX series*) and INS-4020/4040

Optional accessories for the INS-AX2 series, INS-AX series and INS-4020/4040 Optional accessories for the INS-AX2 series Optional accessories for the INS-4020/4040

---

Optional accessories for the INS-AX2 series, INS-AX series and INS-4020/4040

COUPLING ADAPTOR MODEL: CA-803A
	Connected to the INS series Impulse Noise Simulator, Coupling adaptor Model CA-803A can couple noises generated by the simulator to the cable only by clamping it.
	Click here for enlargement	FEATURES: The user does not need to cut the cable to inject noises to the signal, DC, AC or Ground line of the equipment under test. The user can perform a test for the immunity level of the each part, block, unit or component composing the equipment under test. Direct noise injection into the signal line enabling effective checking of the level of noise immunity. The cable to be tested of up to 15mm in diameter can be put through the CA-803. SPECIFICATIONS Input voltage: 2000V max. Input pulse width: 50ns - 1µs Output voltage: 1/20 of the input voltage ±10% Dimensions: (W)160 x (H) 60 x (D) 35 mm Weight: Approx. 400g INCLUDED ACCESSORIES CA-803 main unit (1 pc). Connecting cable 1M NMHV(P)-NMHV(P) (1 pc.) Instruction manual (1 pc.)
	NOTICE: When the CA-803A is used with the INS-410, INS-420, INS-420A or INS-4400 series Simulator, an optional conversion cable is required.
	COUPLING ADAPTOR MODEL: CA-805B The coupling adaptor Model: CA-805B is designed to detect an electric circuit with less noise margin or test the influence of noise by inserting the signal line, DC line, AD line and ground line of the equipment under test and injecting noise from Impulse Noise Simulator INS series.
	Click here for enlargement	FEATURES Injection of noise without cutting the signal line, DC line, AC line and ground line of the equipment under test. Inspection of the level of noise immunity of the electronic equipment for each block or unit. Direct noise injection into the signal line enabling effective checking of the level of noise immunity. Signal line bundle of a maximum of 30 mm SPECIFICATIONS Input voltage: 4000V max. Input pulse width: 50ns - 1µs Dimensions: (W)350 x (H) 120x (D)130 mm Weight: Approx. 3 kgs INCLUDED ACCESSORIES CA-805B main unit (1 pc). Coaxial cable for input/output 1.5m/ Model: 02-00025A (2 pcs.) Instruction manual (1 pc.)
	NOTICE: When the CA-805B is used with INS-400 or INS-4400 series Simulator, an optional cable is required.
	COUPLING ADAPTOR CA-806 MODEL: 15-00007A      For additional product information, please download the CA-806 brochure.(80 Kbyte) Coupling adaptor CA-806 (Model: 15-00007A) is an optional accessory for transient immunity test to wire harnesses with using INS or FNS series simulator.
				FEATURES Easy noise injection.......By only clamping power or signal lines this probe provides an noise injection test without connecting to the lines directly. Diameter 27mm...... Accommodates cables to be tested up to 27mm. Coupling ratio 10:1......Coupling ratio of 10:1, widely used in Automotive electronics industry. SPECIFICATIONS Input voltage: 2000V max. Input pulse width: 50ns - 1µs Terminator: Built-in 50 ohm terminator Coupling ratio: 10:1 Diameter for clamping cable: 27mm max. Connector: NMHV type Dimensions: (W) 64 x (H) 89x (D)120 mm Weight: Approx. 1 kgs INCLUDED ACCESSORIES Connection cable NMHV(P)-NMHV(P) (1 pc.) Instruction manual (1 pc.)
	NOTICE: When the CA-806 is used with INS-400 or INS-4400 series Simulator, an optional cable is required.
	RADIATION PROBE MODELS: 01-00006A/00007A/00008A/00009A/ 00010A Connected to the INS Impulse Noise Simulator, Radiation Probe gives radiated interference to the circuit, PC board or unit to be tested, allowing the user to know where are the parts or blocks which are sensitive to radiated noise.
			SPECIFICATIONS Input voltage: 4000V max. Input pulse width: 50ns - 1µs Radiation loop diameter Model 01-00006A: 50 mm Model 01-00007A: 75 mm Model 01-00008A: 100 mm Model 01-00009A: 150 mm Model 01-00010A: 200 mm Cable length: Approx. 2m Weight: Approx. 200g
	ATTENUATOR MODEL: AT-810 This attenuator is designed to observe square waves with fast rise time or high voltage pulses with triangular waves such as the output waveforms of impulse noise simulators (Models: INS series) and Fast Transient/Burst Simulators (Models: FNS series).
	Click here for enlargement		FEATURES Attenuates high voltage pulse of up to 4000V to 100:1. Wide band attenuation of DC 5 to 500 MHz. SPECIFICATIONS Input voltage: 4000V max. Input pulse width: 50ns - 1µs Attenuation ratio: 1:100 (40dB) Input impedance: 50 ohm Output impedance: 50 ohm Frequency characteristics: DC to 500MHz (-4dB) Weight: Approx. 550 g
	EMS PROBE KIT MODEL: H2B
	Click here for enlargement			A diagnostic tool for locating sensitive spots on the circuits under test to the electric or magnetic transient field. This kit consists of 3 electric and 3 magnetic field probes, all in a different probe head size for a variety of applications. Connected to the INS or FNS (Electrical Fast Transient Burst ) simulator, each probe works as a transient field source. FEATURES Detects possible noise immunity problem spots Generates transient electrical and magnetic fields separately Application for modules, components, conductors and ICs Suited for the connection to the FNS or INS series simulator Convenient handling by pencil shape, light plug-type cable with snap-action coupling.

Top of this page

	OUTLET PANEL MODEL: 18-00069A		OUTLET PANEL MODEL: 18-00070A
	JP/USA type, AC125V 20A MAX		CEE7/Schuko type, AC240V 16A MAX
	OUTLET PANEL MODEL: 18-00071A		CIRCUIT BREAKER BOX MODEL:18-00072A Single phase AC240V20A 50/60Hz, DC65/20A
	Multiple type, AC240V 15A MAX		CIRCUIT BREAKER BOX MODEL:18-00073A 3-phase AC415V50A 50/60Hz
	MERCURY RELAY UNIT for replacement MODEL: 04-00014A for INS-AX2-220/250 MODEL: 04-00015A for INS-AX2-420/450		OPTICAL INTERFACE BOX MODEL: 07-00022A