Top  >  Lightning Surge Simulator (LSS)  >  Lightning Surge Simulator LSS-6330 series

Lightning Surge Simulator LSS-6330 series

Lightning Surge Simulator   LSS-6330 series

A tester simulatively generates "High energy induced lightning noise" which induced to distribution lines or communication lines by ground potential fluctuation caused by lightning strikes.

 

  • Conforming to IEC 61000-4-5 Ed.3, IEC61000-4-12 Ed.3(RINGWAVE 100kHz)and ANSI IEEE62-45(2002) *
  • Pre-checking function simplifies start-up inspection works.
  • Voltage and current monitors enable status monitoring during noise applied to EUT.
  • Large LCD operation panel improve visibility and operability.
  • MPU control function simplifies continuous testing, enables automatic surge-out, waveform-switching and polarity switching.
  • Equipped with both manual and program mode to simplify test condition setting. Manual mode: for standard and single-shot testing. Program mode: for different testing in succession.
  • Interlocking function provides excellent safety.
  • Standardly equipped waveform checking terminals provide easy output waveform checking with existing oscilloscope and BNC cables.
  • Isolation transformer available for safety protection for superimposing circuit current leakage and back surge to power source.(Option)

* For Ring Wave coupling, simultaneous application is possible only for the Basic test type with PE as surge COM.

Pre-checking function simplifies start-up inspection works

<Conventional>: It requires for two expensive high voltage probes and differential measurement available oscilloscope for start-up inspection works.

<LSS-6330>: Simplifies start-up inspection works only by connecting dedicated cables to the tester to confirm whether or not the output is present. (pre-checking). (Available for SURGE OUTPUT/EUT LINE OUTPUT)

 

 

*Photos are under development.

 


Visualize the testing connection status on monitor display for easy testing condition understanding

Monitor screen displays connection status in order to avoid incorrect power line connection. In addition, an outlet box (option) simplifies testing connection.

 

 

 


Incorporated “Emergency stop” and “Interlock function” to improve operation safety.

Equipped with operation safety functions in both hardware and software. Safety sockets as well as emergency stop switches and interlock terminals secure operation safety when connecting EUT. In addition, further safety is available by using “protection fences” and “protection boxes”. (option)

 

 

 


Waveform checking terminal enables output waveform monitoring

We received many market feedbacks say “I want to check the output waveform during the test”, the answer is “Yes we can”. We incorporated the checking terminal, and it enables monitoring of applied waveforms to EUT via oscilloscopes during tests. Furthermore, even without oscilloscopes, you could check the voltage & current value on the upgraded monitor screen as well.

 

 


PC control software simplifies overall test processes

It is so easy to set complicate test sequences of various test types, save test results & records and generate test reports.

※Software download available on the Web.

 

 


Multilingual localization provides easy test condition setting

Multilingual touch panel display supports easy and sure test setting. Languages in English, Chinese, Korean and Japanese.

 


 


Specification

■ Surge generator unit LSS-6330-A20 / -B63 both applicable

Item Specification Note
Coupling Surge Waveform 1.2/50μs-8/20μs combination
10/700μs-5/320μs combination
RING WAVE
 
1.2/50μs-8/20μs
combination
Output voltage(open circuit) 0.5kV-6.7kV ±10% Coupling circuit: 18μF
Cable length: 0.5m on one side
Line input side open
Front time voltage waveform / Duration 1.2μs ±30% / 50μs ±20%
Output current(short circuit) 250A- 3350A ±10%
Front time current waveform / Duration 8μs ±20%/ 20μs ±20%
10/700 μs-5/320μs
combination
Output voltage(open circuit) 0.5kV-6.7kV ±10% Cable length: 0.5m on one side
Front time voltage waveform / Duration 10μs ±30%/ 700μ s±20%
Output current(short circuit) 12.5A-167.5A ±10%
Front time current waveform / Duration 5μs ±20% / 320μs ±20%
RING WAVE Output voltage(open circuit) 0.25kV-6.6kV ±10% Cable length: 0.5m on one side
Front time voltage waveform 0.5μs ±30%
Frequency 100kHz ±10%
Attenuation Pk2 = 40% < Pk1 < 110%Pk2 = 40% < Pk1 < 110%
Pk3 = 40% < Pk2 < 80%Pk3 = 40% < Pk2 < 80%
Pk4 = 40% < Pk3 < 80%
Output current(short circuit) 8.3-550A±10%
Front time current waveform 0.2-1μs
Palarity Positive / Negative  
Output impedance 2Ω±10% 1.2/50μs waveform
40Ω±10% 10/700μs waveform
12Ω±20%、30Ω±20% RING (selective)
Surge generation circuit Floating  
Minimum charging time 0.0kV-4.0kV:5 s、 4.1kV-6.7kV:10 s 1.2/50μs waveform
0.0kV-4.0kV:10 s、 4.1kV-6.7kV:15 s 10/700μs waveform
0.0kV-4.0kV:1 s、 4.1kV-6.6kV:3 s RING WAVE
Communication RS-232C (Optical connector), Bluetooth Option
External CDN control  
Emergency stop Push-lock(Test STOP, High voltage OFF, EUT switch SHUT OFF)  
Interlock function External connection status detection  
Emergency lamp Red LED blinking after start the tests  
Emergency lamp connector Equiped with emergency lamp connectors. Lamp blinking after start the tests. 3ports
EUT Fail 3 ports  
Voltage monitor BNC output、2000V/V ±10% Simplified open circuit surge out checking
Current monitor BNC output、1000A/V ±10% Simplified short circuit surge out checking
Phase angle control 0°-360°±10° Operates at EUT power supply AC90V min. &  50Hz / 60Hz ± 10%
Trigger input Asynchronous, AC line synchronous 0°-360° / 1° step、external input  
 
Drive power supply AC100V-AC240V ±10% 50Hz / 60Hz ±10%  
Operating environment
 

Temperature: 15-35℃

Humidity: 25-75%RH

 
Dimensions/ Weight W430×H371×D530 mm / Approx. 55kgs  

■ Superimposed Output Section LSS-6330-A20

Item  Specification  Note
Coupling Surge Waveform 1.2/50μs-8/20μs combination, RING WAVE  
1.2/50μs-8/20μs
combination
Output voltage 0.5kV-6.7kV ±10% Coupling circuit: 18μF
Cable length: 0.5m on one side
Line input side open
Front time/ Duration 1.2μs ±30% / 50μs ±20%
Short-circuit current 250A-3350A ±10%
Front time/ Duration 8μs ±20%/ 20μs ±20%
Output voltage 0.5kV-6.7kV ±10% Coupling circuit: 10Ω+9μF
Cable length: 0.5m on one side
Line input side open
Front time/ Duration 1.2μs ±30% / 50μs +10μs /-25μs
Short-circuit current 41.6A-558A ±10%
Front time/ Duration 2.5μs ±30%/ 25μs ±30%
RING WAVE Output voltage 0.25kV-6.6kV ±10% Coupling circuit:4.5μF
Cable length: 0.5m on one side
Line input side open
Front time 0.5μs ±30%
Frequency 100kHz ±10%
Attenuation rate Pk2 = 40% < Pk1 < 110%Pk2 = 40% < Pk1 < 110%
Pk3 = 40% < Pk2 < 80%Pk3 = 40% < Pk2 < 80%
Pk4 = 40% < Pk3 < 80%
Short-circuit current
 
8.3 〜 550A±10%
Front time 0.2 〜 1μs
EUT power capacity
 
AC240V/20A MAX 50/60Hz、DC125V/20A MAX  
Decoupling coil 1.5mH  
Voltage drop Less than 10% of rated voltage when rated current is applied At the output terminal of the AC superposition section
 
Residual voltage 15% or less of the applied surge voltage or twice or less of the rated voltage (peak value) of the power supply line
 
 

■ Superimposed Output Section LSS-6330-B63

Item  Specificaion  Note
Coupling Surge Waveform 1.2/50μs-8/20μs combination, RING WAVE  
1.2/50μs-8/20μs
combination
Output voltage 0.5kV-6.7kV ±10% Coupling circuit: 18μF
Cable length: 0.5m on one side
Line input side open
Front time/ Duration 1.2μs ±30% / 50μs ±20%
Short-circuit current 250A-3350A ±10%
Front time/ Duration 8μs ±20% / 20μs ±20%
Output voltage 0.5kV-6.7kV ±10% Coupling circuit: 10Ω+9μF
Cable length: 0.5m on one side
Line input side open
Front time/ Duration 1.2μs ±30%/ 50μs +10μs /-25μs
Short-circuit current 41.6A-558A ±10%
Front time/ Duration 2.5μs ±30%/ 25μs ±30%
RING WAVE Open voltage 0.25kV-6.6kV ±10% Counpling circuit: 4.5μF
Cable length: 0.5m on one side
Line input side open
Front time 0.5μs ±30%
Frequency 100kHz ±10%
Attenuation rate

Pk2 = 40% < Pk1 < 110%

Pk3 = 40% < Pk2 < 80%

Pk4 = 40% < Pk3 < 80%

Short-circuit current 8.3-550A±10%
Front time 0.2-1μs
EUT power capacity AC600V/63A MAX 50/60Hz、DC125V/63A MAX  
Decoupling coil 1.5mH  
Voltage drop Less than 10% of rated voltage when rated current is applied At the output terminal of the AC superposition section
Residual voltage 15% or less of the applied surge voltage or twice or less of the rated voltage (peak value) of the power supply line
 
 
Phase angle control 0°-360° ±10° Operates at EUT power supply AC90V min. &  50Hz / 60Hz ± 10%
Drive power supply AC100V- AC240V ±10% 50Hz / 60Hz ±10%  
Operating environment
 
Temperature:15-35℃
Humidity: 25-75%RH
 
Dimensions W430 × H695 × D686 mm  

*Requires an isolation transformer separately.

 

 

 


EMC-271